Presentation PerformanceCheck (DPPC)

懒猴航海

REPORTING FORM - ENC/ECDIS Data Presentation and Performance Check for Ships    Page 1: Reporting Form Information

If, as a result of the data presentation and performance checks, any significant operational deficiency is observed, then mariners should contact the manufacturer or service agent directly to seek assistance. Where there are differences with the figures expected from the checks, it may be helpful to provide screenshots using a digital camera. Please include those screenshots with this reporting form if it is convenient.

Please fill out a form for each system on board that uses ENCs

General Information
What is the ECDIS manufacturer’s name?  

Name of manufacturer if not included in the list above ?  

What is the name and/or number of the ECDIS software: (for example: ACME Sailor 4000)?  

What is the software build / version number of the software ?  

When were the checks performed?   

Optional Information

This will enable the IHO to contact you if more information or clarification is required.
Your name or the name of the vessel will not be used for any purpose other than to contact you for clarification and further feedback if required.

You do not need to give your name of the name of your ship if you don’t want to.

What is the name of your vessel or organization?  

Who is the best point of contact?  

What is the contact address or email for the point of contact?  

Would you be prepared to answer follow up questions? (Tick YES or NO) YESNO

懒猴航海

Report of Your Results

Preliminary Question

Were you able to load both of the check ENC cells ? (Tick YES or NO) YESNO

Figure 2

Check 1 - Display of navigation areas recently recognised by the IMO

Question 1 - Are the charted objects 1 to 4 being displayed as shown in figure 2? (Tick YES or NO)

Question 1 - does object 1 display as in fig. 2? YESNO

Comment (Q1 - obj1) If "NO" - what is being displayed?  

Question 1 - does object 2 display as in fig. 2? YESNO

Comment (Q1 - obj2) If "NO" - what is being displayed?  

Question 1 - does object 3 display as in fig. 2? YESNO

Comment (Q1 - obj3) If "NO" - what is being displayed?  

Question 1 - does object 4 display as in fig. 2? YESNO

Comment (Q1 - obj4) If "NO" - what is being displayed?  

懒猴航海

懒猴航海 发表于 2016-7-9 07:57
Report of Your ResultsPreliminary Question
Were you able to load both of the check ENC cells ? (Tic ...

Page 3

Figure 3

Check 2 - Display of complex lights

Question 2 - Are the coloured arcs depicting the complex lights (objects 1 & 2) displayed in the correct placeas shown in Figure 3 ?
(For object 1 there should be separate green and yellow arcs ; for object 2, the red, green and yellow arcs should be displayed outside the single yellow arc.) (Tick YES or NO).

Question 2 - does object 1 display as in fig. 3? YESNO

Comment (Q2 - obj1)- if "NO" - what is being displayed?  

Question 2 - does object 2 display as in fig. 3? YESNO

Comment (Q2 - obj2)- if "NO" - what is being displayed?  

Question 3 - Are the period and range details for the all round light (object (3)) being displayed as Q(5) R2s 10M or Q(5) R2.5S 10M ? Both are acceptable according to the standards. (Tick YES or NO)

Question 3 - does the text for object 3 display exactly as in fig 3? YESNO

If your ECDIS does not show “Q(5) R2s 10M or Q(5)R2.5s 10M, please indicate what is shown:

懒猴航海

懒猴航海 发表于 2016-7-9 07:58
Page 3
Figure 3
Check 2 - Display of complex lights

Page 4

Figure 4

Check 3 - Display of underwater features and isolated dangers

Question 4a - Are the underwater features (objects 1 to 8) being displayed as shown in figure 4?
Mark YES even if you see the following additional information: "?", "Rep" or "PA". (This additional information is a capability provided by some manufacturers that is more than the minimum requirements of the ECDIS Performance Standard).

Question 4a - does object 1 display as in fig. 4? YESNO

Comment (Q4a - obj1). If NO - what is being displayed ?  

Question 4a - does object 2 display as in fig. 4? YESNO

Comment (Q4a - obj2).  If NO - what is being displayed ?  

Question 4a - does object 3 display as in fig. 4? YESNO

Comment (Q4a - obj3). If NO - what is being displayed ?  

Question 4a - does object 4 display as in fig. 4? YESNO

Comment (Q4a - obj4). If NO - what is being displayed ?  

Question 4a - does object 5 display as in fig. 4? YESNO

Comment (Q4a - obj5). If NO - what is being displayed ?  

Question 4a - does object 6 display as in fig. 4? YESNO

Comment (Q4a - obj6). If NO - what is being displayed ?  

Question 4a - does object 7 display as in fig. 4? YESNO

Comment (Q4a - obj7). If NO - what is being displayed ?  

Question 4a - does object 8 display as in fig. 4? YESNO

Comment (Q4a - obj8). If NO - what is being displayed ?  

Question 4b - Are any other objects being displayed in the same general area in addition to objects 1 to 8 ?  (Tick YES or NO)

Question 4b - any other features or symbols being displayed in addition to objects 1 to 8?  YESNO

Comment (Q4b Add Fea)- if yes, what other objects (symbols) are being displayed?  

---

Question 5 - With display mode set to "OTHER", "FULL" or "ADDITIONAL", is the symbol for “foul area of seabed safe for navigation but not for anchoring” (object 9) being displayed as shown in fig 5? (Tick YES or NO)

Figure 5

Question 5 - does object 9 display as in fig 5 ? YESNO

Comment (Q5 - Obj9) - if NO - what is being displayed?  

---

Question 6 - With display mode still set to "OTHER", "FULL" or "ADDITIONAL", are there other underwater features (object 1 to 8 in fig 4) displayed as in figure 5 ? (Tick YES or NO)

Question 6 - does object 1 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj1) If NO - what is being displayed?  

Question 6 - does object 2 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj2) If NO - what is being displayed?  

Question 6 - does object 3 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj3) If NO - what is being displayed?  

Question 6 - does object 4 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj4) If NO - what is being displayed?  

Question 6 - does object 5 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj5) If NO - what is being displayed?  

Question 6 - does object 6 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj6) If NO - what is being displayed?  

Question 6 - does object 7 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj7) If NO - what is being displayed?  

Question 6 - does object 8 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj8) If NO - what is being displayed?  

---

Question 7a - Were you able to successfully change the safety depth setting to 8 metres before conducting the next step of the checks?  (Tick YES or NO)

Question 7a - you were able to change the safety depth setting to 8 metres ? YESNO

Figure 6

Question 7b - With the safety contour/safety depth set at 8 metres, is the symbol for “underwater hazard with adefined depth” (object 10) being displayed as shown in fig 6 ?
It should be a depth of 8,5 contained in a dotted oval/circle with a blue infill. (Tick YES or NO)

Question 7b - does object 10 display as in fig. 6? YESNO

Comment (Q7 - obj 10) If NO - what is being displayed?  

---

Question 8 - With the safety contour/safety depth still set at 8 metres are all underwater features (objects 1 to 7 and object 9) displayed as in figure 6) ? (Tick YES or NO)

Question 8 - does object 1 still display as in figure 6? YESNO

Comment (Q8 -Obj1) If NO - what is being displayed?  

Question 8 - does object 2 still display as in figure 6? YESNO

Comment (Q8 -Obj2) If NO - what is being displayed?  

Question 8 - does object 3 still display as in figure 6? YESNO

Comment (Q8 -Obj3) If NO - what is being displayed?  

Question 8 - does object 4 still display as in figure 6? YESNO

Comment (Q8 -Obj4) If NO - what is being displayed?  

Question 8 - does object 5 still display as in figure 6? YESNO

Comment (Q8 -Obj5) If NO - what is being displayed?  

Question 8 - does object 6 still display as in figure 6? YESNO

Comment (Q8 -Obj6) If NO - what is being displayed?  

Question 8 - does object 7 still display as in figure 6? YESNO

Comment (Q8 -Obj7) If NO - what is being displayed?  

Question 8 - does object 9 still display as in figure 6? YESNO

Comment (Q8 -Obj9) If NO - what is being displayed?  

懒猴航海

懒猴航海 发表于 2016-7-9 07:58
Page 3
Figure 3
Check 2 - Display of complex lights

Page 4

Figure 4

Check 3 - Display of underwater features and isolated dangers

Question 4a - Are the underwater features (objects 1 to 8) being displayed as shown in figure 4?
Mark YES even if you see the following additional information: "?", "Rep" or "PA". (This additional information is a capability provided by some manufacturers that is more than the minimum requirements of the ECDIS Performance Standard).

Question 4a - does object 1 display as in fig. 4? YESNO

Comment (Q4a - obj1). If NO - what is being displayed ?  

Question 4a - does object 2 display as in fig. 4? YESNO

Comment (Q4a - obj2).  If NO - what is being displayed ?  

Question 4a - does object 3 display as in fig. 4? YESNO

Comment (Q4a - obj3). If NO - what is being displayed ?  

Question 4a - does object 4 display as in fig. 4? YESNO

Comment (Q4a - obj4). If NO - what is being displayed ?  

Question 4a - does object 5 display as in fig. 4? YESNO

Comment (Q4a - obj5). If NO - what is being displayed ?  

Question 4a - does object 6 display as in fig. 4? YESNO

Comment (Q4a - obj6). If NO - what is being displayed ?  

Question 4a - does object 7 display as in fig. 4? YESNO

Comment (Q4a - obj7). If NO - what is being displayed ?  

Question 4a - does object 8 display as in fig. 4? YESNO

Comment (Q4a - obj8). If NO - what is being displayed ?  

Question 4b - Are any other objects being displayed in the same general area in addition to objects 1 to 8 ?  (Tick YES or NO)

Question 4b - any other features or symbols being displayed in addition to objects 1 to 8?  YESNO

Comment (Q4b Add Fea)- if yes, what other objects (symbols) are being displayed?  

---

Question 5 - With display mode set to "OTHER", "FULL" or "ADDITIONAL", is the symbol for “foul area of seabed safe for navigation but not for anchoring” (object 9) being displayed as shown in fig 5? (Tick YES or NO)

Figure 5

Question 5 - does object 9 display as in fig 5 ? YESNO

Comment (Q5 - Obj9) - if NO - what is being displayed?  

---

Question 6 - With display mode still set to "OTHER", "FULL" or "ADDITIONAL", are there other underwater features (object 1 to 8 in fig 4) displayed as in figure 5 ? (Tick YES or NO)

Question 6 - does object 1 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj1) If NO - what is being displayed?  

Question 6 - does object 2 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj2) If NO - what is being displayed?  

Question 6 - does object 3 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj3) If NO - what is being displayed?  

Question 6 - does object 4 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj4) If NO - what is being displayed?  

Question 6 - does object 5 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj5) If NO - what is being displayed?  

Question 6 - does object 6 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj6) If NO - what is being displayed?  

Question 6 - does object 7 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj7) If NO - what is being displayed?  

Question 6 - does object 8 still display as in figs. 4 and 5? YESNO

Comment (Q6 - Obj8) If NO - what is being displayed?  

---

Question 7a - Were you able to successfully change the safety depth setting to 8 metres before conducting the next step of the checks?  (Tick YES or NO)

Question 7a - you were able to change the safety depth setting to 8 metres ? YESNO

Figure 6

Question 7b - With the safety contour/safety depth set at 8 metres, is the symbol for “underwater hazard with adefined depth” (object 10) being displayed as shown in fig 6 ?
It should be a depth of 8,5 contained in a dotted oval/circle with a blue infill. (Tick YES or NO)

Question 7b - does object 10 display as in fig. 6? YESNO

Comment (Q7 - obj 10) If NO - what is being displayed?  

---

Question 8 - With the safety contour/safety depth still set at 8 metres are all underwater features (objects 1 to 7 and object 9) displayed as in figure 6) ? (Tick YES or NO)

Question 8 - does object 1 still display as in figure 6? YESNO

Comment (Q8 -Obj1) If NO - what is being displayed?  

Question 8 - does object 2 still display as in figure 6? YESNO

Comment (Q8 -Obj2) If NO - what is being displayed?  

Question 8 - does object 3 still display as in figure 6? YESNO

Comment (Q8 -Obj3) If NO - what is being displayed?  

Question 8 - does object 4 still display as in figure 6? YESNO

Comment (Q8 -Obj4) If NO - what is being displayed?  

Question 8 - does object 5 still display as in figure 6? YESNO

Comment (Q8 -Obj5) If NO - what is being displayed?  

Question 8 - does object 6 still display as in figure 6? YESNO

Comment (Q8 -Obj6) If NO - what is being displayed?  

Question 8 - does object 7 still display as in figure 6? YESNO

Comment (Q8 -Obj7) If NO - what is being displayed?  

Question 8 - does object 9 still display as in figure 6? YESNO

Comment (Q8 -Obj9) If NO - what is being displayed?  

懒猴航海

Page 5

Figures 7

Check 4 – Detection of objects by route checking in voyage planning mode

Question 9 - In voyage planning mode, when you check the direct route between “Start” and “End” does the ECDIS provide any indication or alarm for the six charted objects ?
Also, if the symbols displayed do not match those in figure 7, please provide details.

Question 9(Obj1) - does the ECDIS provide any indication or alarm? YESNO

Comment (Q9 - Obj1) Provide details if symbol is different to fig.7 / Other comments ?  

Question 9(Obj2) - does the ECDIS provide any indication or alarm? YESNO

Comment (Q9 - Obj2) Provide details if symbol is different to fig.7 / Other comments ?  

Question 9(Obj3) - does the ECDIS provide any indication or alarm? YESNO

Comment (Q9 - Obj3) Provide details if symbol is different to fig.7 / Other comments ?  

Question 9(Obj4) - does the ECDIS provide any indication or alarm? YESNO

Comment (Q9 - Obj4) Provide details if symbol is different to fig.7 / Other comments ?  

Question 9(Obj5) does the ECDIS provide any indication or alarm? YESNO

Comment (Q9 - Obj5) Provide details if symbol is different to fig.7 / Other comments ?  

Question 9(Obj6) - does the ECDIS provide any indication or alarm? YESNO

Comment (Q9 - Obj6) Provide details if symbol is different to fig.7 / Other comments ?  

Any other Comments - If you have any other comments to make about the performance of your ECDIS in relation to the IHO standards, please include them here:

Any Other Comments (Q9) ?  

Final Checks:

• Have you completed a form for each different ECDIS using ENCs on board?
• Have you any screenshots showing differences from the expected results?
• On completion of the checks, did you return the ECDIS settings to the values required for safe navigation in your ship?